IBM Aptiva 2124 Скачать руководство пользователя страница 43

Страница: 43 / 310

General Information 1-3

−

Intel Pentium

–350, 400, 450 MHz internal, 100 MHz external

(2139)

−

Intel Celeron

–300, 333 MHz internal, 66 MHz external

(2153/Celeron)

Memory

•

512-KB Pipeline Burst Static RAM (PBSRAM). Fixed onboard for 2153/K6,
built-in Pentium

processor

for

2139, 128-KB PBSRAM built-in Celeron

processor for 2153/Celeron.

•

Onboard fixed video Synchronize Graphics RAM (SGRAM), 2- or 4-MB for
Machine Type 2153, 4-MB for 2139.

•

168-pin synchronous dynamic random access memory (SDRAM), dual
inline memory module (DIMM) sockets.

−

2 memory sockets for Machine Type 2153, 3 sockets for 2139.

−

16-MB, 32-MB, 64-MB or 128-MB DIMM.

−

PC-100(64-bit, non ECC, 100MHz, 3.3volt) DIMMs with gold
contacts.(PC-66 for 2153/Celeron)

−

For 2153, maximum memory is 256MB, for 2139 maximum
memory is 384MB.

External Ports

•

Video port (15-pin D-sub connector)

•

Parallel port (25-pin D-sub connector)

•

Serial port (9-pin D-sub connector)

•

Game/MIDI port (15-pin D-sub connector)

•

Keyboard port (6-pin PS/2 mini-din connector)

•

Mouse port (6-pin PS/2 mini-din connector)

•

Two USB ports

•

Microphone-in jack

•

Speaker-out jack

•

Line-in jack

Diskette Drive

•

AT-type

Содержание Aptiva 2124























































































































































































































































































































Результаты поиска

Содержание Aptiva 2124

Отзывы:

Похожие инструкции для Aptiva 2124

Бренды по названию

Популярные бренды

IBM Aptiva 2124, Техническое обслуживание оборудования

Результаты поиска

Содержание Aptiva 2124

Отзывы:

Похожие инструкции для Aptiva 2124

Бренды по названию

Популярные бренды