IBM 3409-S03 Скачать руководство пользователя | Manualshive

Страница: 35 / 82

background image

Configured for direct dock SATA, the system operates with one module. The other compute module bay
must be filled with a blank module. The presence of compute modules is checked when the power is
turned on. The enclosure does not turn on if the compute module is not present. An alarm occurs when
incompatible configurations are detected.

The enclosure chassis is keyed to prevent compute modules from being inserted upside down.

Figure 20. AP-LS-1 module

Chapter 2. System overview

19

«
...
33
34
35
36
37
...
»

Содержание 3409-S03



















































































Отзывы:

Нет отзывов

Похожие инструкции для 3409-S03

DataTraveler Locker+ Generation 3 DTLPG3

Бренд: Kingston Technology Страницы: 1623

Taylor-Wharton XL-65

Бренд: Harsco Страницы: 26

My Passport for Mac

Бренд: Western Digital Страницы: 2

StorNext QM1200

Бренд: Quantum Страницы: 9

Бренд: National Instruments Страницы: 20

SmartStore SM2020

Бренд: Riverlea Страницы: 16

Бренд: M-Systems Страницы: 22

Бренд: Sanyo Страницы: 8

Бренд: Sanyo Страницы: 26

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 4

VAIO PCGA-HD740

Бренд: Sony Страницы: 7

Бренд: Sony Страницы: 16

VAIO VGP-UHDP04

Бренд: Sony Страницы: 23

Vaio VGP-UHDM10

Бренд: Sony Страницы: 27

VAIO VGP-UHDM08

Бренд: Sony Страницы: 27

Бренд: Sony Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды