25
GB
GB
Warning!
Before proceeding, ensure that engine is
switched off and key is removed from starter switch.
When you receive the lawn tractor, the cutting deck is
separate from the tractor.
Assembly of cutting deck is done, firstly by mounting deck
support frame and then the cutting deck itself.
1 Fit the two ends of the frame fully home in the short tubes
welded to tractor frame (Fig. 6.1).
2 Press down so as to align the terminal holes with those of
the tubes.
3 At this point, insert the two pins to secure the cutting
device (A) and the safety split pins (B). (Fig. 6.2).
4 Lift deck support frame using pedal (1) and lock with lever
(2) (Fig. 3.1).
5 Position mowing deck (13) in front of the tractor and push
it underneath.
6. Insert the engine belt into the control pulley site
(transmission of the motion to plate) paying attention that
the belt stretcher is properly positioned (Fig.6.3). Make
sure that the belt is perfectly adherent to the pulley site.
7. Lower the plate support frame, then fasten the plate with
the four pivots that are also required to adjust the cutting
height.
8. Make sure all the belts are properly in tension (see
paragraph 8.7)
9. Lift the plate support frame by acting on the pedal (1) and
lever (2) (fig.3.1) then turn the seat forward and insert the
grass exhaust tube into the flexible tube leading to the
turbin.
To remove, follow operations listed above in reverse order.
6
- ASSEMBLY / REMOVAL OF THE CUTTING DECK
7 -
STARTING MACHINE
7.1 – ADJUSTING MOWER HEIGHT
Warning!
Before making any adjustments, stop
engine and remove starter key.
Important!
Blades continue to rotate for a few seconds, after
the machine has been stopped: before making any
adjustments ensure blades have come to a complete stop.
Mowing height can be set from a minimum of 33 mm to a
maximum of 70 mm.
To make this adjustment, lower the mowing deck by releasing
lever (2) and using pedal (1) (Fig. 3.1).
Remove the four split-pins inserted in the four frame posts that
hold mower deck in position.
Raise or lower mower deck using handle shown in figure 7.1.
Adjust cutting height of deck by inserting split-pins in one of
the five holes provided on the fastening posts.
7.2 – ADJUSTING SEAT POSITION
Warning!
! Before making any adjustments, stop
engine and remove starter key.
Before making this adjustment, sit on the seat to check that
pedal controls are easy to reach. If not, lift the seat, loosen
the 4 fixing nuts and adjust the seat (Fig. 7.2) on the 4 slots
so that when you are sitting in the operating position, all
foot/hand operated controls are easy to reach.
Lower seat by moving the locking device on the left lower
corner of the seat.
7.3 - RAISING MOWING DECK
When moving machine from storage to work area or around
the cutting area itself, you must lift the mowing deck to
facilitate these movements.
Do this by fully pressing down pedal (1) located to the left of
the steering-column, and once deck is raised, lock it in
position by pressing the small lever (2) with your right foot.
Release pedal (1) until cutting unit remains in the raised
position.
At this point, with mowing deck raised, follow the instructions
(chapter 7.4) for proceeding to work area.
Содержание Vision IB-VAC15C4H
