manualshive.com logo in svg

iBall Baton iB-WRA150N, Руководство пользователя

Поделиться
Скачать
iBall Baton iB-WRA150N Скачать руководство пользователя страница 67

iB-WRA150N

  150M Wireless-N ADSL2+ Router - User Guide

 

¾

 

Remote IPSec Gateway Address

: Enter the destination gateway IP address in the box 

which is the public WAN IP or Domain Name of the remote VPN server endpoint. (For 
example: Input 219.134.112.247 in Device1, Input 219.134.112.246 in Device 2) 

¾

 

Tunnel access from local IP addresses

: Choose Subnet if you want the Whole LAN to join 

the VPN network, or else choose Single Address if you want single IP to join the VPN 
network. 

¾

 

IP Address for VPN

: Enter the IP address of your LAN. (For example: Input 192.168.1.1 in 

Device1, Input 192.168.2.1 in Device2) 

¾

 

IP Subnetmask

: Enter the Subnet mask of your LAN. ( For example: Input 255.255.255.0 in 

both Device1 and Device2) 

¾

 

Tunnel access from remote IP addresses

: Choose Subnet if you want the Remote Whole 

LAN to join the VPN network, or else choose Single Address if you want single IP to join the 
VPN network. 

¾

 

IP Address for VPN

: Enter the IP address of the Remote LAN. ( For example: Input 

192.168.2.1 in Device1,Input 192.168.1.1 in Device2) 

¾

 

IP Subnetmask

: Enter the subnetmask of the remote LAN. ( For example: Input 

255.255.255.0 in both Device1 and Device2) 

¾

 

Key Exchange Method

: Select Auto (IKE) or Manual. 

¾

 

Authentication Method

: Select Pre-Shared Key (recommended) or Certificate (X.509). 

¾

 

Pre-Shared Key

: Input the Pre-Shared key for Authentication. (For example: Input 12345678) 

¾

 

Perfect Forward Secrecy

: PFS is an additional security protocol. 

We recommend you leave the Advanced Settings as default value. 

After complete the basic settings and click 

Save/Apply

 in both Device1 and Device2, PCs in LAN1 

could communicate with PCs in remote LAN2. (For example: You can ping the IP address of PC2 
which is 192.168.2.100 in PC1) 

)

 

Note: 

The VPN Servers Endpoint from both ends must use the same pre-shared keys and Perfect 
Forward Secrecy settings. 

Click 

Show Advanced Settings

 and then you can configure the Advanced Settings. 

¾

 

Main Mode

: Select Main Mode to configure the standard negotiation parameters for IKE 

phase1. 

¾

 

Aggressive Mode

: Select Aggressive Mode to configure IKE phase1 of the VPN Tunnel to 

carry out negotiation in a shorter amount of time. (Not Recommended-Less Secure) 

)

 

Note: 

The difference between the two is that aggressive mode will pass more information in fewer 
packets, with the benefit of slightly faster connection establishment, at the cost of transmitting the 
identities of the security firewall in the clear. When using aggressive mode, some configuration 
parameters such as Diffie-Hellman groups, and PFS can not be negotiated, resulting in a greater 
importance of having "compatible" configuration on both ends. 

62 

Содержание iB-WRA150N






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды