background image

SAFETY WARNINGS AND GUIDELINES 

Please read this entire manual before using this device, paying extra attention to these 
safety warnings and guidelines. Please keep this manual in a safe place for future 
reference. 

 

This device is intended for indoor use only.

 

Do not expose this device to water or moisture of any kind. Do not place drinks 
or other containers with moisture on or near the device. If moisture does get in 
or on the device, immediately unplug it from the power source and allow it to 
fully dry before reapplying power. 

 

Do not touch the device, the power cord, or any other connected cables with 
wet hands. 

 

Do not expose this device to excessively high temperatures. Do not place it in, 
on, or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it
in direct sunlight. 

 

Prior to operation, check the units and power adapters for physical damage. Do 
not use if physical damage has occurred. 

 

Take care to prevent damage to the power cord. Do not allow it to become 
crimped, pinched, walked on, or become tangled with other cords. Ensure that 
the power cord does not present a tripping hazard. 

 

Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body. 

 

Ensure that power is turned off and disconnected before making any electrical 
connections. 

 

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or 
detergents. For stubborn deposits, moisten the cloth with warm water. 

 

This device has no user serviceable parts. Do not attempt to open, service, or 
modify this device. 

Содержание MN-H-C5-8211 HDMI















Отзывы: