Hyundai F4GE9454J*J604 Скачать руководство пользователя страница 70

Страница: 70 / 142

From timing side, remove the cover (2) loosening the
screws (1) in order to have access to the union fixing nut
(3) to the pump driving gear.

Loosen the fixing nut (3) and remove the relating
washer.

From the pump side, loosen the fixing nuts (1) without
removing them in order to enable moving the pump
backwards using 99340035 extractor.

Assemble the 99340035 extractor throughout the two
threaded ports (4, Figure 99) and withdraw the gear from
the pump shaft.

Properly hold the feed pump and loosen completely the
fixing nuts.

Withdraw the pump from the studs, together with the
gasket.

When the supply pump is to be assembled on the engine the
P.M.S. conditions at compression end stage cylinder No. 1
must be carried out.

Figure 98

Unscrew the side screw that locks the pump shaft
partially (1) and remove spacer (2). This must be kept on
a side (we recommend to fix it on the pump with a wire
or a clip).

Tighten the lateral screw (1) blocking rotation of the
pump shaft.

Figure 99

Figure 100

75693

75694

Hold the pump driving gear to avoid interference
or crawling during timing gear rotation.

75721

BOSCH VE 4/12 F Pump

NOTE

SECTION 3 - AGRICULTURAL APPLICATION

F4GE N SERIES

Base - February 2009

Print P2D32N010 E

Содержание F4GE9454J*J604















































































































































Результаты поиска

Содержание F4GE9454J*J604

Отзывы:

Бренды по названию

Популярные бренды

Hyundai F4GE9454J*J604, Техническое и ремонтное руководство

Результаты поиска

Содержание F4GE9454J*J604

Отзывы:

Бренды по названию

Популярные бренды