Hyundai F4GE9454J*J604 Скачать руководство пользователя страница 68

Страница: 68 / 142

Figure 93

87712

Reassemble the starter;
properly hold the starter (2) and tighten the fixing screws
(1) to the prescribed couple.

Figure 94

75673

On the left hand side:

Assemble oil filter (1) together with bracket (for the
versions with engine oil filter not directly assembled to
the exchanger); tighten the screws (3) assembling the
bracket (4) including filter bearing (5).
Using tool 99360076 screw up oil filter;

The plug and the oil filler pipe (for versions with the
engine oil filter fitted directly on the heat exchanger);

Assemble oil level rod together with guide pipe (2).

Fill up engine oil.

Install the engine on the machine (for installation
operations please apply to specific issue).

SECTION 3 - AGRICULTURAL APPLICATION

F4GE N SERIES

Base - February 2009

Print P2D32N010 E

Содержание F4GE9454J*J604















































































































































Результаты поиска

Содержание F4GE9454J*J604

Отзывы:

Бренды по названию

Популярные бренды

Hyundai F4GE9454J*J604, Техническое и ремонтное руководство

Результаты поиска

Содержание F4GE9454J*J604

Отзывы:

Бренды по названию

Популярные бренды