background image

S825/1 

 

 

 

ENVIRONMENTAL INFORMATION 

 

European  Directive  2012/19/EU  requires  that  the 
equipment bearing this symbol on the product and/or its 
packaging  must  not  be  disposed  of  with  unsorted 
municipal waste.  The symbol indicates that this product 
must  be  disposed  of  separately  from  regular  household 
waste streams.  It is your responsibility to dispose of this 
and  other  electric  and  electronic  equipment  via 
designated  collection  facilities  appointed  by  the 
government or local authorities.

 

 

 

 

IMPORTANT WARNING NOTES 

1. This meter is only be used to measure diesel or liquids classed as cat. 3 

in  accordance  with  European  Regulation  No.  1272/2008.  It  must  not  be 
used to measure petrol or any other liquid with a similar flash point. 

2. This  product  must  not  be  used  if  it  is  damaged  or  leaking,  located  in  a 

fully enclosed environment or not provided with adequate ventilation. 

3. Installation  of  this  equipment  and  its  associated  tank,  pipe  work  and 

fittings  should  only  be  carried  out  by  qualified  fuel  installation  engineers 
and  must  conform  to  the  latest  relevant  electrical  and  local  authority 
regulations and standards. 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание HO Series









Отзывы: