5.
Check that all wheel parts are correctly installed. If instal-
lation is not correct, remove all of the air pressure from the
tire. Remove the valve core to make sure all of the air pres-
sure has been removed and then make adjustments. The
clearance at the ends of the lock ring will be approximately
13 to 25 mm (0.5 to 1.0 in.) when the tire has the correct air
pressure.
Install the Wheels
Install the wheel on the hub. On the drive wheels tighten
the nuts in a cross pattern to a torque value of 450 to
500 N•m (332 to 369 lbf ft). If the wheels are the two-piece
rims, make sure the nuts that fasten the rim halves together
are toward the brake drum when they are installed.
The steering wheels are fastened to the spindle of the
steering axle with a large castle nut. Make sure inner and
outer bearings are correctly lubricated with grease. Install
inner bearing assembly and wheel on spindle. Install outer
bearing cone and castle nut. Tighten castle nut to 60 N•m
(44 lbf ft) while wheel is rotated. Loosen castle nut until hub
turns freely with no end play. Tighten castle nut to 3.0 to
6.0 N•m (425 to 850 lbf in). Install cotter pin in castle nut. If
the cotter pin cannot be installed, loosen the castle nut to
the first position where the cotter pin can be installed.
Install cap for bearings.
Pneumatic Tubeless Tire, Repair
Remove Tire From Lift Truck
WARNING
Wheels must be changed and tires repaired by trained
personnel only.
Deflate tires completely before removing the wheel
from the lift truck. If dual wheels are used, deflate both
tires. Air pressure in the tires can cause the tire and
rim parts to explode causing serious injury or death.
Always wear safety glasses.
Never loosen the nuts that hold the inner and outer
wheels halves together when there is air pressure in
the tire.
The Tubeless Bead Seal (TBS) enables tubeless tires to be
used on wheel rims that were designed to be used with a
tube.
The main component of the TBS is a special rubber ring
that fits inside the tire between the tire beads to ensure the
Maintenance
157
Содержание H40-60XT
