background image

  WARNING 

Cleaning  solvents  can  be  flammable  and  toxic,
and  can  cause  skin  irritation.  When  using  clean-
ing solvents, always follow the recommendations
of the manufacturer.

4. 

Inspect  the  sideshift  cylinder.  See  the  section
Cylinder  Repair  (Mast  S/N  A270-72,  A551,
A555,  A559,  A626,  A627,  A751-52,  B551,
B555,  B586-91,  B749-54,  C661-63,  C665,
D507-09,  D515,  D562-64,  E509,  E564)

2100SRM1382 for procedures.

5. 

Inspect  load  rollers  for  wear  and  damage.  If
load  rollers  must  be  replaced,  make  a  note  of
the location and number of the shims to ensure
correct installation.

Assemble

1. 

Assemble the sideshift cylinder. See the section
Cylinder  Repair  (Mast  S/N  A270-72,  A551,
A555,  A559,  A626,  A627,  A751-52,  B551,
B555,  B586-91,  B749-54,  C661-63,  C665,
D507-09,  D515,  D562-64,  E509,  E564)

2100SRM1382 for procedures.

2. 

If  lube  fittings  were  removed,  install  new  lube
fittings into outer frame. See Figure 10.

NOTE:   

Use  a  wood  block  or  a  plastic  hammer  to

fully seat the upper bearings onto the inner frame.
Proper  lower  hook  clearance  requires  the  upper
bearings be fully seated.

3. 

Apply a 1 mm (0.040 in.) layer of multipurpose
grease to upper and lower bearing surfaces. In-
stall the upper and lower bearings onto the in-
ner  frame.  Bearings  snap  into  place.  See  Fig-
ure 13.

Install

1. 

Use  a  crane  with  a  capacity  of  at  least
450 kg (992 lb) to install the outer frame on the
inner frame.

2. 

Install  the  lower  mounting  hooks  using  four
capscrews.  Tighten  to  165  ±15  N•m  (120
±12 lbf ft). For proper sideshift operation, make
sure there is 0.76 to 1.52 mm (0.03 to 0.06 in.)
clearance between the bottom of the hooks and
the outer frame. See B in Figure 12.

3. 

Connect the hydraulic lines, as noted during re-
moval, to the sideshift cylinder.

4. 

Install  the  backrest  on  the  sideshift  carriage.
See  Figure  8.  Tighten  the  capscrews  to
195 N•m (144 lbf ft).

5. 

Install the forks. See the section Fork Replace-
ment for the procedures.

Carriages Repair

4000 SRM 1386

18

Содержание A935 J1.6-2.0XN


























Отзывы: