HygroMatik FlexLine Скачать руководство пользователя | Manualshive

Страница: 18 / 56

background image

Page 18

5.4 Steam Manifold

5.4.1 General installation guidelines

When installing steam manifolds, pls. follow
these guidelines:

Positioning within duct

•

Install the steam manifold as close as
possible to the steam humidifier in
order to minimize steam loss through
condensation

•

Steam manifold placement on the sup-
ply side of the air duct is preferable

•

Install steam manifold strictly horizontal
in order to ensure proper condensate
drain

•

Shown installation and positioning
dimensions are based on empiric
values. Special environmental conditi-
ons may require adjustments. Pay
special attention to avoid condensate
generation in air duct

Allowable pressures

•

Max. allowable pressure in air duct is
1500 Pa/.218 PSI (exemption: SLE02
only allows for 1200 Pa/.174 PSI)

•

On the suction side, max. -500 Pa (.07
PSI) is tolerable

•

With high-pressure air conditioning
systems, modifications of the unit‘s
drain hose system may possibly be
required depending on the overall pres-
sure situation. These modifications
must be

coordinated with your

expert dealer.

Water drain

•

It is advisable to provide a water drain
within the absorption distance inside
the air duct. Though not of relevance
here, we point out that this is a must
when the accordance to the German
Association of engineers (VDI) guide-
line VDI 6022 is to be met.

When increased airflow speed is encoun-
tered

•

Air flow rates beyond 3m/s (9.84 ft/s)
may lead to condensate drainage prob-
lems at the steam manifolds due to
vacuum built-up. A possible remedy is
twisting the steam manifold in its hori-
zontal axis by few angular degrees. In
case of problems, pls. consult your
expert dealer.

5.4.2 Recommendations for dimen-

sioning

The recommendations given below are
based on homogenous air flow in the duct.

Horizontal installation of steam manifold

Standard steam manifold arrangement:

An even distribu-
tion of steam ma-
nifolds ensures a
uniform steam
distribution.
Please use the
total hight of the
duct!

L1=L2=L3

Air flow
direction

Steam manifold
(Side view)

Air duct

*) s. table of manifold lengths

Horizontal assembly position in duct

l*) (depends on duct dimension)

4.7 inch

120 mm

2.8 inch

70 mm

90 mm

3.5 inch

1.5 mm

.06 inch

«
...
16
17
18
19
20
...
»

Содержание FlexLine

























































Отзывы:

Нет отзывов

Похожие инструкции для FlexLine

Бренд: KESNOS Страницы: 24

Бренд: Zibro Страницы: 24

Бренд: Levoit Страницы: 36

Бренд: Ultra-air Страницы: 20

Бренд: lifeSMART Страницы: 10

Бренд: Therma-Stor Страницы: 11

Бренд: Champion Страницы: 12

Бренд: Champion Страницы: 20

Бренд: Sanyo Страницы: 4

Бренд: UFESA Страницы: 40

Бренд: Trotec Страницы: 60

Бренд: Ideal Air Страницы: 4

Бренд: Munters Страницы: 20

Бренд: Elechomes Страницы: 6

Бренд: Easy@Home Страницы: 36

Бренд: Vector Страницы: 8

Бренд: Base aire Страницы: 15

Бренд: Bionaire Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды