manualshive.com logo in svg

Hydronix HV04, Руководство пользователя

Поделиться
Скачать
Hydronix HV04 Скачать руководство пользователя страница 51

Chapter 5 

System Navigation 

Hydro-View User Guide HD0531 Rev 2.0.0 51 

Unscaled 2 (only shown for selected sensors) 

For sensors which support this option, this shows the current Measurement Mode used to 
calculate the Unscaled 2 reading. Touch to change. For further details of the Measurement 
Modes, refer to the Calibration and Configuration Guide HD0679. 

Material Temperature Alarm Low/High  

The Material High and Low Limits are used to configure the Material Temperature alarm. If 
Digital Input/Output 2 is set to Material Temperature Alarm the output will become active if 
the material temperature sensor is above the high limit or below the low limit. 

Alarm Mode 

Configures which Measurement Mode (Mode F, Mode V, Mode E or Legacy) is used to 
calculate the alarm values. The Alarm Mode is only available for sensors with multi 
Measurement Mode capabilities. Once configured, the sensor will only calculate the alarm 
values using the selected Measurement Mode. The Alarm Mode will also configure which 
Measurement Mode is used to calculate the AutoTrack values. 

6.6 

Factory Settings Screen 

The Calibration and Configuration Guide HD0679  should be read and understood 
before attempting to change these parameters. 

 

6.6.1 

Factory Settings 

 

Figure 34: Factory Settings Screen 

Water/Air   

These show the Air and Water points used to calculate the Unscaled readings. These are 
set in the factory and should not be manually entered. 

AutoCal   

When fitting a new Sensing Arm to a Hydro-Probe Orbiter, or replacing the ceramic on a 
Hydro-Mix the Air and Water factory calibrations need to be updated. However, if the 
sensor is installed in a mixer, it is not always possible to manually perform the air and 
water readings. To help with this issue an alternative function called AutoCal may be used. 
This makes an air reading and then estimates the water reading based on a constant air-
water difference. 

When using AutoCal with a Hydro-Probe Orbiter certain arm types require the selection of 
the type and length before this calibration starts. The arm type and length is set on the 
Digital Inputs/Outputs Screen (Page 46).  

 

Содержание HV04






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды