background image

Recommended Placement Positions

The RO assembly should be positioned in one of two ways. 
The first position is with the unit standing upright using the support 

leg with the sumps horizontal. The tubing is directed to provide the 

best fit.
The second position, sets the unit on end so the sumps are pointing 

up. The tubing is directed upward and the locking bar is down to lock 

the tubing connections. See Figure 9  System Positions. 

NOTE: Ensure that the support leg is installed on the sumps.

 

Connection Lubrication

Connections with O-rings must be properly lubricated. The following 

instructions describe the method and locations for lubrication.
Six packets of silicone lube are supplied. One packet should be 

completely used to lubricate the O-ring contact surfaces in the 3 

manifold ports and 2 RO membrane locations (Figure 10). Follow 

Figure 11 and lubricate the filter seat and the flat surface below the 

threads for the 3 sump locations. Use a complete packet of silicone 

for each sump location.

NOTE: To properly lubricate the O-ring contact area, a film of clean 

silicone grease is applied. The film should cover all of the 

surface area that the O-ring will slide over and seal with. Do 

not use grease containing petroleum products.

NOTE: The Quick Start guide indicates applying the lube directly to 

the O-rings as opposed to the contact surfaces of the O-rings. 

Either method is appropriate.

NOTE: Please save extra lube packs for future membrane changes. 

Extra lube packs can be sourced through your dealer, Hydro-

Logic, plumbing supply stores, or hardware stores.

INSTALLATION cont.

 System Positions

Figure 3 

First Position

Locking Bar

Second Position

Support Leg

 

Figure 4 

 

Figure 5 

8

Содержание EVOLUTION-RO1000

















Отзывы: