Hydro-Gear HGM-C Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

Hydro-Gear HGM-C Скачать руководство пользователя страница 9

HGM-C LSHT Wheel Motor

7

Gearwheel Set (17)

Cardan Shaft (15)

O-ring (18)

GEARWHEEL SET

Figure 9, Gearwheel Set

Disassembly

1. Remove castellated nut (1), woodruff key

(6), plastic plugs (8), retaining ring (2),

seven screws (22), seven washers (23), and

the end cover (19).

See pages 5 and 6

.

2. Remove the O-ring (18) and gearwheel set

(17). Discard O-ring (18).

See figure 9.

Note:

Placing fingers underneath gearwheel

set will help keep parts from falling
out.

3. Remove second O-ring (16), under gear-

wheel set, and discard.

4. Dismantle the gearwheel set for inspection

if contamination or damage is suspected.

Inspection

1. Inspect for wear or damage.

CARDAN SHAFT

Disassembly

1. Remove castellated nut (1), woodruff key

(6), plastic plugs (8), retaining ring (2),

seven screws (22), seven washers (23),

end cover (19), and the gearwheel set (17)

with O-rings (16, 18).

See figure 4 - 7

.

2. Remove the cardan shaft (15).

See figure 10.

Inspection

1. Check for wear and/or damage to the indi-

vidual splines on the cardan shaft (15).

Figure 10, Cardan Shaft

«
...
7
8
9
10
11
...
»

Содержание HGM-C

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды