Hydro-Gear HGM-C Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

background image

HGM-C LSHT Wheel Motor

9

Housing (9)

Output Shaft (7)

Ball Bearing (3)

NEEDLE BEARING

SHAFT SEAL

Figure 14, Needle Bearing

Disassembly

1. Remove castellated nut (1), woodruff key

(6), plastic plugs (8), retaining ring (2), seven

screws (22), seven washers (23), end cover

(19), gearwheel set (17) with O-rings (16, 18),

cardan shaft (15), distributor plate (14), O-

ring (13), output shaft (7) and the shaft seal.

See pages 4 - 9.

2. Remove the needle bearing (12) with a

pressing tool.

See figure 14.

Note:

The needles may fall out of the needle

bearing (12) during dismantling and can
be retrieved for re-use.

Inspection

1. Inspect for wear or damage.

Disassembly

1. Remove castellated nut (1), woodruff key

(6), plastic plugs (8), retaining ring (2),

seven screws (22), seven washers (23), end

cover (19), gearwheel set (17) with O-rings

(16, 18), cardan shaft (15), distributor plate

(14), O-ring (13), and the output shaft (7).

See pages 4 - 8.

2. Using a holding tool, press ball bearing (3),

washer (4), and shaft seal (5) off the output

shaft (7).

See figure 13.

Inspection

1. Inspect for wear or damage.

Figure 13, Output Shaft Seal

«
...
9
10
11
12
13
...
»

Содержание HGM-C

























Отзывы:

Нет отзывов

Похожие инструкции для HGM-C

Бренд: Painless Performance Страницы: 24

Бренд: Atlas Copco Страницы: 156

Бренд: Econex Страницы: 14

Бренд: Beckhoff Страницы: 31

Бренд: Briggs & Stratton Страницы: 14

Бренд: Deutz Страницы: 257

Бренд: Man Страницы: 18

Бренд: Kubota Страницы: 309

Бренд: Louvolite Страницы: 4

Бренд: Electric Drive Engineering Страницы: 19

Бренд: BLACKHAWK! Страницы: 60

Бренд: Baumuller Страницы: 23

Бренд: Alutech Страницы: 32

Бренд: Honda Страницы: 42

Бренд: DLE Страницы: 4

12K300 INTEK series

Бренд: Briggs & Stratton Страницы: 16

PS01-37x120F-HP-SSC-R/ FC

Бренд: LinMot Страницы: 40

2232***BX4 series

Бренд: Faulhaber Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды