Hydro-Gear HGM-C Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 24

Hydro-Gear HGM-C Скачать руководство пользователя страница 6

4

HGM-C LSHT Wheel Motor

Cotter Pin

Castellated Nut (1)

Drum Assembly

Brake Assembly

Bolt (29)

HGM Motor

Disassembly

1. Remove the cotter pin.

See figure 1.

2. Remove the castellated nut (1).

See figure

1.

NOTE:

If the drum assembly or hub assembly

is removed from the axle shaft, the

drum/ hub assembly must be discarded

and replaced with a new assembly.

3. Remove the drum assembly.

See figure 1.

4. Remove the four bolts (29) securing

the brake assembly to the HGM motor.

See figure 2.

5. Remove the brake assembly.

See figure 2.

Inspection

1. Inspect the studs on drum for wear and/or

damage. Replace if necessary.

2. Inspect the brake assembly, i.e., the brake

shoes for wear and/or damage.

Assembly

1. Reassemble all parts in the reverse order

of disassembly.

2. When tightening the fasteners, refer to the

table on page 3 for the required torque val-

ues.

NOTE:

As a general rule, use the low end of

the torque specification on fasteners
when reassembling the unit.

DRUM & BRAKE ASSEMBLY

Figure 1, Drum Assembly

Figure 2, Brake Assembly

«
...
4
5
6
7
8
...
»

Содержание HGM-C

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды