Hydro-Gear HGM-C Скачать руководство пользователя страница 18

Страница: 18 / 24

HGM-C LSHT Wheel Motor

Figure 17, Washers & Screws

Gearwheel (17)

Rim

End Cover (19)

Figure 15, Gearwheel Set

Assembly

1. Install the end cover (19).

See figure 16.

Align markings.

2. Install

new

washers (23) onto the end cover

screws (22).

See figure 17.

Note:

When tightening the screws, refer to the

table on page 3 for the required torque
values. Also refer to figure 18 for the
proper torque sequence.

Figure 16, End Cover

END COVER

Assembly

4. In gearwheel set (17) with non-through

splines place the gearwheel set (17) with

the recess in the spline hole facing down

towards the motor housing (9).

5. Fit the gearwheel set (17) on the cardan

shaft (15) so that the top of the tooth in the

external teeth of the gearwheel is vertically

over the mark on the cardan shaft.

6. Turn the gearwheel set (17) counter clock-

wise until the cardan shaft (15) and the

internal gearwheel slips over and engages

the splines.

7. Turn the gearwheel rim to line up the

screw holes.

See figure 15.

Alignment

marks made before disassembly should

line up.

GEARWHEEL SET

(continued)

Top of Tooth

Mark

Cardan Shaft (15)

Screw (22)

Washer (23)

Содержание HGM-C

























Результаты поиска

Содержание HGM-C

Отзывы:

Бренды по названию

Популярные бренды

Hydro-Gear HGM-C, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание HGM-C

Отзывы:

Бренды по названию

Популярные бренды