Hydro-Gear HGM-C Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

6

HGM-C LSHT Wheel Motor

End Cover (19)

Screw (22)

Disassembly

1. Remove castellated nut (1), woodruff key

(6), plastic plugs (8), and retaining ring (2).

See page 5.

2. Using a 13mm wrench — remove the seven

screws (22).

See figure 7.

3. Remove the seven washers (23) and dis-

card.

4. Remove the end cover (19) by sliding the

end cover sideways, off the gearwheel set.

See figure 8.

Inspection

1. Inspect for wear or damage.
2. Inspect screws (22) – threads, for wear or

damage.

END COVER

Figure 7, Screws

Figure 8, End Cover

«
...
6
7
8
9
10
...
»

Содержание HGM-C

























Отзывы:

Нет отзывов

Похожие инструкции для HGM-C

Бренд: VEM Страницы: 16

Бренд: Jabiru Страницы: 103

Бренд: JetCat Страницы: 74

Бренд: Motolux Страницы: 2

Бренд: 3W Страницы: 20

Бренд: Cadillac Страницы: 36

Бренд: Nissei Страницы: 16

Бренд: Yamaha Страницы: 30

Бренд: Volvo Penta Страницы: 122

Бренд: Lycoming Страницы: 194

Бренд: Honda Страницы: 4

Бренд: Honda Страницы: 48

Бренд: Honda Страницы: 71

Бренд: Honda Страницы: 80

Бренд: O.S. engine Страницы: 4

BREVINI V Series

Бренд: DANA Страницы: 34

Бренд: Volvo Penta Страницы: 176

Бренд: WEN POWER Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды