HydraMaster TITAN 425 страница 50 Скачать руководство пользователя

Страница: 50 / 55

TITAN 425 Owner’s Guide

Check the engine valve clearance (intake and

exhaust 0.004” - 0.006”)

Change pump drive belt.

Change sacrificial anodes.

Quarterly Maintenance

1000 Hours Maintenance

Clean and gap the spark plugs to 0.030”.

Replace if excessive carbon buildup is visible.

Replace coupler element (rubber insert) for

cracks or wear.

Change the high pressure pump oil.

Check coupler element (rubber insert) for cracks

or wear. Replace as necessary.

Change the blower oil.

Change the fuel filter.

Check plug wires. Replace as necessary

Change air filters.

Change pump drive belt.

500 Hours Maintenance

100 Hours Maintenance

Clean the heat exchanger core.

Check carburetor. Clean or replace as

necessary.

Check the fuel lines. Repair or replace as

needed.

Replace spark plugs

250 Hours Maintenance

Check coupler element (rubber insert) for cracks

or wear. Replace as necessary.

Change the fuel filter.

Содержание TITAN 425
























































Результаты поиска

Содержание TITAN 425

Отзывы:

Похожие инструкции для TITAN 425

Бренды по названию

Популярные бренды

HydraMaster TITAN 425, Руководство пользователя и график технического обслуживания

Результаты поиска

Содержание TITAN 425

Отзывы:

Похожие инструкции для TITAN 425

Бренды по названию

Популярные бренды