HydraMaster TITAN 425 страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 55

background image

TITAN 425 Owner’s Guide

-

28

Oil Filter

Briggs and Stratton engines use Briggs and Stratton oil filters. An equivalent or better oil

filter must be used when servicing the engine.

To replace the filter, use a proper filter wrench to remove the filter.

Clean the filter mounting base and lightly coat the gasket surface of the new filter with

engine oil. Hand tighten the filter until the gasket contacts the base, then tighten another

½ turn. Fill the engine with the correct amount of oil, run the engine and check for oil leaks

at the drain plug and oil filter gasket.

Spark Plugs

Always use the recommended spark plugs for your engine. Hotter or colder plugs, or similar

plugs that are not exact equivalents to the recommended plugs, can cause permanent

engine damage, reduce the engines useful life, and cause many other problems such as

hard starting, spark knock and run-on. Installing new spark plugs regularly is one of the

best ways to keep your engine at peak performance.

Fuel Filter

The fuel filter is located between the fuel pump and the fuel tank underneath the vehicle.

«
...
28
29
30
31
32
...
»

Содержание TITAN 425
























































Отзывы:

Нет отзывов

Похожие инструкции для TITAN 425

Manual Tower Controller

Бренд: Vinpower Страницы: 2

Бренд: Fluke Страницы: 2

Бренд: Crestron Страницы: 5

Бренд: KLD Страницы: 4

Бренд: Englefield Страницы: 7

Бренд: First Alert Страницы: 4

Бренд: First Alert Страницы: 8

Бренд: Aqua Medic Страницы: 18

Бренд: IDBLUE Страницы: 24

Бренд: Tetra Страницы: 60

Бренд: 3M Страницы: 23

B125 ACTIVE BALANCE CONTROL

Бренд: EMG Страницы: 4

Бренд: ZKTeco Страницы: 24

Бренд: Eaton Страницы: 46

Бренд: Olymp Страницы: 6

Бренд: IceCap Страницы: 2

Бренд: Olympus Страницы: 24

Бренд: dentronix Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды