manualshive.com logo in svg

HydraMaster Boxxer 423s, Руководство пользователя

Поделиться
Скачать
HydraMaster Boxxer 423s Скачать руководство пользователя страница 55

8-11:  Systems Troubleshooting

   Systems Troubleshooting:  8-10

VACUUM SYSTEM

1.0 A weak vacuum at wand. The gauge reads normal.

Possible Cause

Solution

1.1 Blockage in the hoses or 

wand tube

Disconnect the hoses and check for an obstruction.

1.2 Excessive length of 

hose connected to the 
truckmount

Do not attach excessive lengths of hose.

2.0 A weak vacuum

Possible Cause

Solution

2.1 Air leak somewhere in the 

vacuum system.

Check the vacuum relief valve for proper adjustment.

Carefully check all the vacuum hoses for a cut or 
break.

Check the recovery tank lid gasket.

Make sure the recovery tank drain valve is fully 
closed.

2.2 The vacuum blower is 

turning too slowly.

Check the rpm of the engine. Adjust as necessary to 
3,200 rpm under no vacuum load.

2.3 The vacuum gauge is 

defective.

Test the gauge and replace if necessary.

3.0 The vacuum gauge reads too high with no hoses attached

Possible Cause

Solution

3.1

The filter in recovery tank 

is clogged.

Remove and clean or replace as necessary.

3.2 The hose from recovery 

tank to the vacuum blower 
is collapsed internally.

Inspect and replace as necessary.

4.0 Excessive noise produced by the blower

Possible Cause

Solution

4.1 The blower is low on oil.

Inspect the oil levels and replenish as necessary. 
Note: Running the blower with low oil levels can cause 
severe damage. If this situation occurs the blower 

should be inspected by a qualified service technician.

4.2 The vacuum blower has 

internal damage. 

Refer to a qualified service technician.

5.0 The vacuum blower is locked and will not turn

Possible Cause

Solution

5.1 Truckmount has been 

inactive for a period of 
time and the blower was 
not properly lubricated 

prior to final shutdown. 

Rust has possibly built up 
on the internal surfaces. 

Spray penetrating oil into the blower and let sit for 
at least 1 hour. Then very carefully use pipe wrench 
on the outer diameter of the pulley on the coupler 
to attempt to free lobes of the blower. Do not use a 
wrench directly on the blower shaft. 

If unable to free up the blower in this manner, refer to 

a qualified service technician.

5.2 There is internal damage 

to the blower.

Refer to a qualified service technician.

6.0 Water in truckmount exhaust

Possible Cause

Solution

6.1 The recovery tank has 

been filled with foam or 

overfilled with water.

Inspect the recovery tank. If full, drain the tank. 

Inspect the high level shutoff switch for proper 
operation. Clean or replace the switch as necessary.

If foam is in recovery tank, use defoamer on the 
carpet being cleaned.

6.2 Condensation in system.

This will be more common in cool weather and humid 
climates. If this is the cause, it should dissipate after 
a few minutes of running.

6.3 The heat exchanger is 

leaking water.

Inspect and repair or replace as necessary.

Содержание Boxxer 423s





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды