Hydmech M16A Скачать руководство пользователя | Manualshive

Страница: 50 / 76

background image

3.12

On V18APC:
The head will swing slowly to 45 L, and then will come forward for a cut. It will retract, then swing slowly to 45 R, come
forward for a cut, and then retract. At this point the procedure is complete.

NOTE:

If doing this procedure using material to scribe and calculate new value, a scribe cut at 90 will have to be made before
starting the procedure.

On M16/20A:
The head will swing to 90 degrees, if not already there, move down for a cut, move back up, and then swing to 30 de-
grees. It will again move down for a cut, and then move back up. At this point the procedure is complete. The line will then

read - ANG CLB “ENTER” OFF At any point after the procedure has started, or after it has finished, move the cursor down

to the TTL MEAS ANG line, type in the desired value (original or adjusted parameter ), and press ENTER. To finish the

procedure, press the AUTO/MANUAL key and the value entered will then be accepted by the PLC.

The above procedure is performed to allow for the original parameter to be reinstalled, in a case where there is no angle
display due to loss of this value by PLC memory (electrical & mechanical components ok), or to allow for the original

parameter to be modified, in a case where the angle display is inaccurate, and proper calibration cannot be performed.

(Proper material not available for test cuts.)

Actual calibration is performed by running the angle calibration procedure with a piece of cold rolled material (6-8’ wide),

allowing the blade to scribe the material, then measuring and calculating the angles cut. (For angle troubleshooting details
please contact Hyd·Mech Group Limited).

PLC 500 E600 input / Output Terminal
Information

Inputs

X0 - Shuttle Encoder, Channel A

X1 - Shuttle Encoder, Channel B

X2 - Blade Speed or Proximity Switch

X3 - Feed rate encoder A / Angle Encoder A

X4 - Feed rate encoder B / Angle Encoder B

X5 - Open

X6 - Head 90° L/S

X7 - Coolant Switch

X10 - Blade Status

X11 - Coolant Switch

X12 - Head Raise L/S

X13 - Head Lower L/S

X14 - Open

X15 - Cycle Start P/B

X16 - Open

X17 - Open

X20 - Shuttle Vise Close Switch

X21 - Shuttle Vise Open Switch

X22 - Front Vise Close Switch

X23 - Front Vise Open Switch

X24 - Head Raise Switch

X25 - Head Lower Switch

Outputs

Y0 - Front Vise Open

Y1 - Front Vise Close

Y2 - Shuttle Fast

Y3 - Encoder Switching Relay

Y4 - Shuttle Vise Open

Y5 - Shuttle Vise Close

Y6 - Open

Y7 - Coolant Pump On / Off

Y10 - Head Lower and Head Lower Relay

Y11 - Head Angle Fast

Y12 - Head Raise
Y13 - Blade Run Relay
Y14 - Shuttle Forward
Y15 - Shuttle Reverse
Y16 - Head Swing 90°
Y17 - Head Swing 30°
Y20 - Machine Latch
Y21 - Open
Y22 - Open
Y23 - Cycle On

«
...
48
49
50
51
52
...
»

Содержание M16A













































































Отзывы:

Нет отзывов

Похожие инструкции для M16A

Бренд: Labnet Страницы: 5

Бренд: CAIRE Страницы: 2

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: OceanSat Страницы: 85

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 13

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 65

Бренд: haacon Страницы: 59

Бренд: PASCO Страницы: 30

Бренд: Gaspardo Страницы: 88

Бренд: RAMVAC Страницы: 53

Бренд: IBC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды