Hydac VMU 1 страница 15 Скачать руководство пользователя

Страница: 15 / 68

Safety information

Improper Use or Use Deviating from Intended Use

DANGER

Danger due to unanticipated use of the unit

Bodily injury and damage to property will result

when operated improperly.

►

Only operate the unit in the atmospheres

allowed.

►

The unit is only to be used with permissible

fluids.

Any use extending beyond or deviating therefrom shall not be considered

intended use. HYDAC Filter Systems GmbH will assume no liability for any

damage resulting from such use. This risk is borne solely by the owner.
Improper use may result in hazards and/or will damage the unit. Examples of

improper use:

•

Operation in potentially explosive atmospheres other than the

identified one.

•

Operation with an impermissible fluid.

•

Operation at an impermissible fluid temperature / ambient

temperature.

•

Operation under non-approved operational conditions.

•

Operation when the safety devices are defective.

•

Operation in mining or in dust-exposed zones

•

Modifications to the power unit made by the user or purchaser.

•

Inadequate monitoring of parts that are subject to wear and tear.

•

Improperly performed repair work.

VMU 1 ATEX II 2G IIC T4

en(us)

Page 15 / 68

BeWa VMU_1_ATEX-II2GIICT4_10000649233 en-us 2017-03-07.doc

2017-03-07

Содержание VMU 1





































































Результаты поиска

Содержание VMU 1

Отзывы:

Похожие инструкции для VMU 1

Бренды по названию

Популярные бренды

Hydac VMU 1, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание VMU 1

Отзывы:

Похожие инструкции для VMU 1

Бренды по названию

Популярные бренды