manualshive.com logo in svg

Huvitz HRK-9000A, Руководство по обслуживанию

Поделиться
Скачать
Huvitz HRK-9000A Скачать руководство пользователя страница 3

2    Auto Ref/Keratometer HRK-9000A ------------------------------------------------------------------------------------------------ 

Important Notice 

 

 

Potential electromagnetic or other interference between medical equipments and 
other devices being operated together in the same environmental may expert an 
adverse  influence  on  functioning  of  the  medical  equipment.   Non-medical 
equipments  not  in  compliance  with  the  requirements  of  EN  60601-1  and  EN 
60601-1-2 should not be used together in the same environmental as the medical 
equipments 

 

This equipment has been tested and found to comply with the limits for medical devices in IEC 
60601-1-2:2001.   These limits are designed to provide reasonable protection against harmful 
interference in a typical medical installation 
 
Power Cord   
For use of equipment in rated voltage less than 125Vac,minimum 6A,Type SJT or SVT, 
18/3AWG, 10A, max 3.0m long : One end with Hospital Grade Type, NEMA 5-15P Other end 
with appliance coupler. For use of equipment in rated voltage less than 250Vac,minimum 
6A,Type SJT or SVT, 18/3AWG, 10A, max 3.0m long : One end terminates with blade 
attachment plug (HAR) Type, NEMA 6-15P. 
 
This product may malfunction due to electromagnetic waves caused by portable personal 
telephones, transceivers, radio-controlled toys, etc. Be sure to avoid having objects such as, 
which affect this product, brought near the product. 
 
The information in this publication has been carefully checked and is believed to be entirely 
accurate at the time of publication. HUVITZ assumes no responsibility, however, for possible 
errors or omissions, or for any consequences resulting from the use of the information 
contained herein. 
 

HUVITZ reserves the right to make changes in its products or product specifications at any time 
and without prior notice, and is not required to update this documentation to reflect such 
changes.

 

 

Ver. 1.0 

 

© 2011 - 2014 - Huvitz Co., Ltd. 

-689-3, Gumjeong-dong, Gunpoci, Gyeonggi-do, 435-862, Republic of Korea 

All rights are reserved. Under copyright laws, this manual may not be copied, in whole or in 

part, without the prior written consent of HUVITZ Co., Ltd.

 

 

!

 

WARNING 

Содержание HRK-9000A














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды