Husqvarna R 418Ts Скачать руководство пользователя страница 5

Страница: 5 / 48

English

– 5

KEY TO SYMBOLS

Symbols

These symbols are on the machine and in the instructions.

WARNING! Careless or incorrect use can
result in serious or fatal injury to the
operator or others.

Please read the operator’s manual
carefully and make sure you understand
the instructions before using the machine.

Always wear:

•

Approved hearing protection

This product is in accordance with
applicable EC directives.

Fast

Slow

Stop the engine.

Choke.

Fuel

Oil level

Cutting height

Backwards

Forwards

Ignition

Hydrostatic freewheel

Parking brake

Noise emission to the environment
according to the European Community’s
Directive. The machine’s emission is
specified in the Technical data chapter and
on the label.

Clutch in

Clutch out

Hot surface.

Cover lock

Warning: rotating parts. Keep hands and
feet clear.

Rotary blades Keep hands and feet
away from under the hood when the
engine is running

Risk that the machine will tip over

Never drive across a slope

Never use the machine if persons,
especially children, or animals, are in the
vicinity

Never carry passengers on the machine or
equipment

Drive very slowly if no cutting unit is fitted

Before and during reversing procedures,
look behind you.

>10

Содержание R 418Ts

















































Результаты поиска

Содержание R 418Ts

Отзывы:

Похожие инструкции для R 418Ts

Бренды по названию

Популярные бренды

Husqvarna R 418Ts, Руководство оператора

Результаты поиска

Содержание R 418Ts

Отзывы:

Похожие инструкции для R 418Ts

Бренды по названию

Популярные бренды