manualshive.com logo in svg

Husqvarna R 418Ts, Руководство оператора, Страница: 43 / 48

Поделиться
Скачать
Husqvarna R 418Ts Скачать руководство пользователя страница 43

English

 – 43

Technical data

Note 1: The power rating of the engine indicated is the average net output (at specified rpm) of a typical production engine for the 
engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ from this value. Actual power 
output for the engine installed on the final machine will depend on the operating speed, environmental conditions and other values.

R 418Ts

R 418Ts AWD

Dimensions

Length without cutting unit, cm/in

202 / 79,5

202 / 79,5

Width without cutting unit, cm/in

90 / 35,4

90 / 35,4

Height, cm/in

113 / 44,5

113 / 44,5

Unladen weight excluding cutting unit, kg/lb

288 / 634,9

299 / 651,2

Wheel base, cm/in

87 / 34,3

87 / 34,3

Track width, front, mm/ft

713 / 2,3

713 / 2,3

Track width, rear, mm/ft

710 / 2,3

710 / 2,3

Tyre dimensions

16 x 6,50 x 8

16 x 6,50 x 8

Air pressure, rear - front, kPa / bar / PSI

60 (0,6/8,5)

60 (0,6/8,5)

Max. gradient

10

10

Engine

Brand / Model

Kawasaki / FS541V

Kawasaki / FS541V

Nominal engine output, kW (see note 1)

10,6

10,6

Displacement, cm

3

/cu.in

603/36,8

603/36,8

Oil, class SC-SH

SAE 30 or SAE 10W/30,  
SAE 10W/40

SAE 30 or SAE 10W/30,  
SAE 10W/40

Oil volume incl. filter

1,9/2.0

1,9/2.0

Oil volume excl. filter, litres/USqt

1,7/1,8

1,7/1,8

Starting

Electric starter

Electric starter

Max.motor speed, r/min

2900 

±

 100

2900 

±

 100

Fuel, minimum octane grade lead-free

87 (max. methanol 5%, max. 
ethanol 10%, max. MTBE 15%)

87 (max. methanol 5%, max. 
ethanol 10%, max. MTBE 15%)

Tank volume, litres/USqt

17/18

17/18

Electrical system

Type

12 V, negative earthed

12 V, negative earthed

Battery

12 V, 24 Ah

12 V, 24 Ah

Spark plug

NGK BPR4ES

NGK BPR4ES

Electrode gap, mm/inch

0,75/0,030

0,75/0,030

Main fuse

Flat pin, 15 A.

Flat pin, 15 A.

Bulbs, halogen

2x12V 20W

2x12V 20W

Transmission

Front axle make

-

KTM 10 SA

Rear axle make

Tuff Torq K 66

Tuff Torq K 664

Oil, class SF-CC

SAE 10W/40

SAE 10W/50 Synthetic

Oil volume, total, litres

3,2

3,2

Cutting unit

Model

Combi 94

Combi 94

Combi 103

Combi 103

Combi 112

Combi 112

Содержание R 418Ts

















































Отзывы:

Нет отзывов