Husqvarna R 418Ts Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 48

Husqvarna R 418Ts Скачать руководство пользователя страница 15

English

– 15

PRESENTATION

Release lever

The release control must be pulled out in order for the
machine to be moved when the engine is shutoff.

Should you attempt to drive the machine with the clutch
controls pulled out it will not move. The drive on the axle is
disengaged when one of the controls is pulled out.

Pull the controls to the end positions, do not use an
intermediate position.

Release lever R 418Ts AWD

R 418 Ts AWD have one control for the front axle and one
control for the rear axle.

•

Clutch control, rear axle

- Control drawn out, drive system disengaged.

- Control depressed, drive system engaged.

•

Clutch control, front axle

The control is positioned on the inside of the left front
wheel.

- Rear control (pulled out), drive system disengaged.

- Front control (pushed in), drive system engaged.

Release lever R 418Ts

•

Pull out the control to disengage the drive system.

•

Push in the control to engage to the drive system.

IMPORTANT! Always drive the machine with both clutch
controls pressed in.

«
...
13
14
15
16
17
...
»

Содержание R 418Ts

















































Отзывы:

Нет отзывов