Husqvarna FE 350 2015 Скачать руководство пользователя страница 199

Страница: 199 / 308

19 CLUTCH

Changing the h draulic clutch fluid

Warning
Skin irritation

Brake fluid causes skin irritation.

Keep brake fluid out of the reach of children.

Wear suitable protective clothing and safety glasses.

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

Consult a doctor immediately if brake fluid has been swallowed.

Rinse the affected area with plenty of water in the event of contact with the skin.

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact with the eyes.

If brake fluid spills on to your clothing, change the clothing.

Warning
Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

(FE EU/ AU/US)

197

Move the clutch fluid reservoir mounted on the handlebar to a horizontal posi

tion.

Remove screws

Remove cover @ with membrane

(D.

(FE 350S US)

Move the clutch fluid reservoir mounted on the handlebar to a horizontal posi

tion.

Remove screws

Remove cover @ with membrane

(D.

Fill bleeding syringe

with the appropriate hydraulic fluid.

Bleed syringe (50329050000) (

!!l

p. 289)

Brake fluid DOT 4 (

!!l

p. 284)

On the clutch slave cylinder, remove bleeder screw

and mount bleeding

syringe

(FE EU/ AU/US)

Inject the liquid into the system until it escapes from openings

of the mas

ter cylinder without bubbles.

Now and then, extract fluid from the master cylinder reservoir to prevent over

flow.

Remove the bleeding syringe. Mount and tighten screws bleeder screw.

Correct the fluid level of the hydraulic clutch.
Guideline

Fluid level below container rim

mm (0.16 in)

Position the cover with the membrane. Mount and tighten the screws.

Содержание FE 350 2015





















































































































































































































































































































Результаты поиска

Содержание FE 350 2015

Отзывы:

Похожие инструкции для FE 350 2015

Бренды по названию

Популярные бренды

Husqvarna FE 350 2015, Руководство по ремонту

Результаты поиска

Содержание FE 350 2015

Отзывы:

Похожие инструкции для FE 350 2015

Бренды по названию

Популярные бренды