Husqvarna FE 350 2015 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 308

background image

15

WIRING HARNESS, BATTERY

109

Main work

\

Insert the battery into the battery compartment with the terminals facing forward.

I

Battery (YTX5L-BS) (

�

p. 215)

Reconnect rubber band

O.

•

Info

I

Contact disks

e

must be mounted under screws

e

and cable sock

ets

0

with the claws toward the battery terminal.

Position the positive cable and mount and tighten the screw.

Guideline

Screw, battery terminal

M5

,__

__

0

---l

-

/1

e

o

Slide positive terminal cover

8

over the positive terminal.

Position the negative cable and mount and tighten the screw.
Guideline

2.5 Nm

(1.84 lbf ft)

Screw, battery terminal

M5

H00387-10

Slide negative terminal cover

fD

over the negative terminal.

Finishing work

Mount the seat. (

�

p. 77)

Recharging the batte

Warning

Risk of injury

Battery acid and battery gases cause serious chemical burns.

Keep batteries out of the reach of children.

-

Wear suitable protective clothing and goggles.

- Avoid contact with battery acid and battery gases.

Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms.

2.5 Nm

(1.84 lbf ft)

In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at

least 15 minutes and contact a physician.

Warning

Environmental hazard

Batteries contain environmentally-hazardous materials.

Do not dispose of batteries as household waste.

Dispose of batteries at a collection point for used batteries.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Info

Even when there is no load on the battery, it discharges steadily.

The charging level and the method of charging are very important for the service life of the battery.

Rapid recharging with a high charging current shortens the service life of the battery.
If the charging current, charging voltage, and charging time are exceeded, the battery will be destroyed.
If the battery is depleted from starting the vehicle repeatedly, the battery must be charged immediately.

If the battery is left in a discharged state for an extended period, it will become over-discharged and sulfated, destroying the

battery.
The battery is maintenance-free, i.e., the acid level does not have to be checked.

Preparatory work

Remove the seat. (

Ill:!

p. 77)

«
...
109
110
111
112
113
...
»

Содержание FE 350 2015





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FE 350 2015

Apache RTR 160 HYPER EDGE 2015

Бренд: TVS Страницы: 60

Бренд: Suzuki Страницы: 230

Бренд: Sym Страницы: 31

Бренд: Malossi Страницы: 36

Бренд: Suzuki Страницы: 26

Бренд: MW TOOLS Страницы: 9

Бренд: Yamaha Страницы: 94

Star XVS13CG 2015

Бренд: Yamaha Страницы: 98

Star XV250G 2015

Бренд: Yamaha Страницы: 88

Star XVS13CTD 2012

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 104

Star XV250H 2016

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: DYNATEK Страницы: 12

Бренд: Dakota Digital Страницы: 14

Бренд: LSL Страницы: 4

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

Бренд: Wunderlich Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды