Husqvarna F2201V1 Скачать руководство пользователя

Страница: 124 / 158

17 SERVICE WORK ON THE ENGINE

122

17.2

Checking the engine oil level

Info

The engine oil level can be checked when the engine is cold or warm.

Preparatory work

–

Stand the motorcycle upright on a horizontal surface.

V01390-10

Condition

The engine is cold.

–

Check the engine oil level.

The engine oil reaches the middle of level viewer

» If the engine oil does not reach the middle of the level

viewer:

–

Add engine oil. (

p. 125)

V01390-11

Condition

The engine is at operating temperature.

–

Check the engine oil level.

Info

After switching off the engine, wait one minute
before checking the level.

The engine oil level is between the middle of the level
viewer

and the upper edge of the level viewer

» If the engine oil does not reach the middle of level

viewer

–

Add engine oil. (

p. 125)

17.3

Changing the engine oil and oil filter, cleaning the oil screen

Warning

Danger of scalding

Engine and gear oil get very hot when the motorcycle is ridden.

–

Wear suitable protective clothing and safety gloves.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Info

Drain the engine oil while the engine is at operating temperature.

Preparatory work

–

Park the motorcycle on a level surface.

Содержание F2201V1































































































































































Результаты поиска

Содержание F2201V1

Отзывы:

Похожие инструкции для F2201V1

Бренды по названию

Популярные бренды

Husqvarna F2201V1, Руководство пользователя

Результаты поиска

Содержание F2201V1

Отзывы:

Похожие инструкции для F2201V1

Бренды по названию

Популярные бренды