Husqvarna F2201V1 Скачать руководство пользователя

Страница: 20 / 158

6 CONTROLS

6.8

Opening fuel tank filler cap

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

V01538-10

(FC 350 EU, FC 350 US)

–

Turn fuel tank filler cap

counterclockwise and lift it off.

V01347-10

(FX 350)

–

Press release button

, turn the fuel tank filler cap

counterclockwise, and lift it off.

Содержание F2201V1































































































































































Результаты поиска

Содержание F2201V1

Отзывы:

Похожие инструкции для F2201V1

Бренды по названию

Популярные бренды

Husqvarna F2201V1, Руководство пользователя

Результаты поиска

Содержание F2201V1

Отзывы:

Похожие инструкции для F2201V1

Бренды по названию

Популярные бренды