Husqvarna F2201V1 Скачать руководство пользователя страница 76

Страница: 76 / 158

11 SERVICE WORK ON THE CHASSIS

K01087-11

–

Position the fuel tank and fit the two spoilers laterally to the
radiator.

–

Make sure that no cables or throttle cables are trapped or
damaged.

K01086-11

(FC 350 EU, FC 350 US)

–

Attach the fuel tank breather hose to the fuel tank lid.

–

Mount and tighten screw

with the rubber bushing.

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

K01085-11

–

Mount and tighten screws

Guideline

Screw, fuel tank
spoiler on radiator

6 Nm (4.4 lbf ft)

V01379-11

–

Plug in connector

for the fuel pump.

–

Remove the wash cap set and thoroughly clean the quick
release coupling using compressed air.

Info

Under no circumstances should dirt enter into
the fuel line. Dirt in the fuel line clogs the injection
valve!

–

Spray silicone spray onto a lint-free cleaning cloth and
lightly lubricate the O-ring of the quick-release coupling.

Silicone spray (

p. 147)

–

Join quick release coupling

Info

Route the cable and fuel line at a safe distance
from the exhaust system.

Содержание F2201V1































































































































































Результаты поиска

Содержание F2201V1

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2201V1, Руководство пользователя

Результаты поиска

Содержание F2201V1

Отзывы:

Бренды по названию

Популярные бренды