Husqvarna 570 AT Скачать руководство пользователя

Страница: 50 / 58

50 – English

PISTON..and..CYLINDER

Pressure.testing

The following parts must be removed to pressure test the

crankcase and cylinder:

• Air filter and carburettor. See page

Carry out pressure testing as follows:

1. Fit both cover pla

te 502 52 48-01 with bolt on the

intake manifold. See fig. 16.

Fit rubber plate 502 54 22-02

between cylinder and

muffler. Cover the exhaust port. See fig. 17.

2. Connect preasure test tool

531 03 06

-23 to tool

502 84 40-02

fitted instead of spark plug. See

fig. 18. The decompression valve should be closed.

3. Pump up the pressure to 80 kPa (0.8 bar).

4. Wait 30 seconds.

5. The pressure must not fall below 60 kPa (0.6 bar).

6. Leakage can occur in the decompression valve and

crankshaft seals.

7. Pressure test the decompression valve as follows.

Se also fig. 19.

A. Connect preasure test tool

531 03 06-23

to the

decompression valve.

B. Pump up the pressure to 80 kPa (0.8 bar).

C. Wait 30 seconds.

D. The pressure must not fall below 60 kPa (0.6 bar).

8. Assemble the following parts:

• Carburettor.

• Cylinder cover. See the Operator's Manual.

• Chain and bar. See the Operator's Manual.

Fig. 16

Fig. 17

Fig. 18

Ax2

Bx2

Fig. 19

Содержание 570 AT



























































Результаты поиска

Содержание 570 AT

Отзывы:

Похожие инструкции для 570 AT

Бренды по названию

Популярные бренды

Husqvarna 570 AT, Руководство по ремонту

Результаты поиска

Содержание 570 AT

Отзывы:

Похожие инструкции для 570 AT

Бренды по названию

Популярные бренды