Husqvarna 570 AT Скачать руководство пользователя

Страница: 4 / 58

SAFETY.REGULATIONS

4 – English

WARNING!.

The. warning. text. warns. of. the. risk. of.

personal. injury. if. the. instructions. are.

not.followed.

General.instructions

The workshop where chainsaw repairs are to be done

must be equipped with safety equipment as set out in

local regulations.

No one may repair the chainsaw unless they have read

and understood the contents of this Workshop Manual.

This Workshop Manual contains the following warning texts

in relevant places. Warning texts are positioned before the

procedures they refer to.

Special.instructions

The fuel used in the chainsaw has the following hazardous

properties:

1. The fluid and its fumes are poisonous.

2. Can cause skin irritation.

3. Is highly inflammable.

The bar, chain and clutch cover (chain brake) must be

fitted before the saw is started otherwise the clutch can

work loose and cause personal injury.

Wear ear-muffs when test running.

Do not use the saw until it has been adjusted so that the

chain remains still when idling.

After test running, do not touch the muffler until it has

cooled. Risk of burn injuries.

Insufficient lubrication of the chain can result in the chain

breaking, which can cause serious or even life-threatening

injury.

Ensure that the spring in the starter does not fly out and

cause personal injury.

If the spring tension is activated on the starter pulley

when it is to be taken up, the spring can fly out and cause

personal injury.

Check that the brake is applied when removing the pressure

spring on the chain brake. Otherwise the pressure spring

can fly out and cause personal injury.

After repair, the chain brake must be checked in accordance

with the instructions on page 16.

When replacing the crankshaft bearings note that the

crankcase halves are hot. Wear protective gloves

Do not direct the compressed air jet towards the body

when using compressed air. Air can penetrate into the

blood circulation, which means mortal danger.

NOTE!.

This.text.warns.of.material.damage.if.the.

instructions.are.not.followed.

Содержание 570 AT



























































Результаты поиска

Содержание 570 AT

Отзывы:

Похожие инструкции для 570 AT

Бренды по названию

Популярные бренды

Husqvarna 570 AT, Руководство по ремонту

Результаты поиска

Содержание 570 AT

Отзывы:

Похожие инструкции для 570 AT

Бренды по названию

Популярные бренды