Husqvarna 570 AT Скачать руководство пользователя | Manualshive

Страница: 18 / 58

background image

STARTER

18 – English

WARNING!.

If.the.spring.is.tensioned.on.the.starter.

pulley.it.can.fly.up.and.cause.personal.

injury.

Wear.protective.glasses.

WARNING!.

If.the.spring.is.tensioned.on.the.starter.

pulley.it.can.fly.up.and.cause.personal.

injury.

Wear.protective.glasses.

Starter

Dismantling

!

Cleaning.and.inspection

Clean all components and check the following:

1. Starter cord.

2. The dogs on the starter pulley.

3. That the pawls on the flywheel are intact, spring

back towards the centre and move freely.

Fig. 1

Fig. 2

Fig. 3

!

4. Remove the central bolt (C) and take out the washer

and starter pulley (D). See fig. 3.

5. If the starter cord is to be replaced, cut it off pull out

the ends from the handle and starter pulley with

pointed pliers.

6. If the spring is to be replaced, remove the screws (E)

and the spring cassette (F).

A

B

E

F

D

C

1. Remove the four bolts holding the starter to the

crankcase and remove the starter. See fig. 1.

2. Pull out the handle 20-30 cm and take out the cord

from the slot in the starter pulley. See fig. 2.

3. Rotate the starter pulley anticlockwise until the ten

sion on the pulley is released.

«
...
16
17
18
19
20
...
»

Содержание 570 AT



























































Отзывы:

Нет отзывов

Похожие инструкции для 570 AT

Бренд: McCulloch Страницы: 14

Бренд: Efco Страницы: 2

Бренд: GardenCare Страницы: 35

Бренд: Makita Страницы: 64

Бренд: Makita Страницы: 34

Бренд: Makita Страницы: 76

Бренд: Makita Страницы: 20

Бренд: Talon Tools Страницы: 6

Бренд: Gasoline Страницы: 17

Бренд: TitanTec Страницы: 20

Бренд: Raider Страницы: 92

Бренд: Makita Страницы: 34

Бренд: Ryobi Страницы: 29

Бренд: Vigor Страницы: 70

Бренд: Protool Страницы: 220

Бренд: Jobsite Страницы: 39

FQ-AKS 4030 BASIC

Бренд: for_q Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды