background image

10

FUEL HANDLING

PROPER FUEL

Taking the following precautions will lessen the risk 

of injury and property damage:

- Use extreme care in handling gasoline. It is  

  extremely flammable and the vapors are explosive.

 

- Extinguish all cigarettes, cigars, pipes, and other               

  sources of ignition.

- Use only approved gasoline containers.

- Never remove gas cap or add fuel with the engine     

  running.  Allow engine to cool a minimum of 3 

  minutes before refueling.

- Never fuel the machine indoors.   

- Never store the machine or fuel container where     

  there is an open flame, spark, or pilot light such as   

  on a water heater or other appliances.

- Never fill containers inside a vehicle or on a truck   

  or trailer bed with a plastic liner. Always place    

  containers on the ground away from your vehicle    

  when filling.

- Remove the 

5000

 from the truck or trailer and 

  refuel it on the ground. If this is not possible, then     

  refuel the equipment with a portable container,    

  rather than from a gasoline dispenser nozzle.

- Keep the nozzle in contact with the rim of the fuel  

  tank or container opening at all times until fueling is  

  complete. Do not use a nozzle lock-open device.

- If fuel is spilled on clothing, change clothing  

  immediately.

- Never overfill fuel tank. Always wipe off any spilled  

  fuel or oil.  Replace fuel cap and tighten

The Kohler engine is certified to operate on automotive un

-

leaded gasoline with a pump octane rating (M+R) of 

87

 or 

higher. Fuel tank capacity is 3.0 gallon (11 liter). 

Refuel in a well-ventilated area with the engine 

stopped

You may use regular unleaded gasoline containing no more 

than 10% ethanol (E10). Do not use gasoline containing 

methanol. 

Use of fuels with an ethanol content of more than 10% (E10) 

may cause starting and/or performance problems. It may also 

damage metal, rubber, and plastic parts of the fuel system, as 

well as posing a fire hazard. 

Do not use fuel that is older than 30 days. Old fuel can cause 

running problems as well as fuel system damage.

The engine will not operate on gasoline 

marketed as E-85 (85% ethanol)

OIL HANDLING

WARNING

  

Used oil is a hazardous waste product.  Dispose  

  of used oil properly.  Do not discard with household 

  waste.  Check with your local authorities, service  

  center, or dealer for safe disposal/recycling facility.

NOTICE

ENGINE OIL

Oil Recommendation

The engine holds approximately 2.1 quart (2.0 liter) when 

changing oil.

- Use a 4-stroke automotive detergent oil of API service class  

  SE or higher grade. 

- Do not use special additives.

- Choose a viscosity according to the table below.

Please read the enclosed Kohler Operator’s Manual for com

-

plete oil information.

HYDROSTATIC TRANS OIL

Mobil DTE 26 

hydraulic oil or equivalent (20W with viscosity 

of 68)

Содержание 5000



















Отзывы: