Husqvarna 2009 HUV 4214 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 57

background image

Air Intake System

AIR INTAKE SYSTEM

AIR FILTER REPLACEMENT

The air filter should be inspected periodically and replaced when necessary. Filter changes should not exceed the
recommended interval.

See Periodic Service Schedule on page 31.

More frequent service may be required in

extremely dirty operating environments. In the event of a loss of power, sluggish acceleration, or a roughly running
engine, service the air filter immediately.

Air Filter Removal

1.

Raise the cargo bed, remove the center plastic access panel (1)

(Figure 16)

and locate the air filter housing.

2.

Release both housing retaining clips

(Figure 27)

.

3.

Lift the housing cover up off of the air filter housing.

4.

Remove knob (1) and plate (2). Carefully remove the foam pre-cleaner (3) and air filter cartridge (4) assembly to
prevent debris from entering carburetor.

See following NOTE.

NOTE:

To clean foam pre-cleaner, separate it from cartridge and wash in liquid detergent and water. Squeeze dry

in a clean cloth. The air filter cartridge and foam pre-cleaner are specifically designed for this engine. Use
only engine-compatible air filter cartridges and foam pre-cleaners designed for your engine. Do not oil
the foam pre-cleaner.

2

3

4

1

817

Figure 27

Air Filter Element

Air Filter Installation

1.

Reassemble clean (or new) pre-cleaner on clean (or new) cartridge.

2.

Place the air cleaner assembly into the air filter housing.

3.

Place the housing cover on the top of the air filter housing.

4.

Secure the housing cover with both retaining clips.

5.

Replace the center plastic access panel (1)

(Figure 16)

and lower and latch the cargo bed.

Page 42

2009 HUV 4214, HUV 4414, andHUV 4414-XP Owner’s Manual

«
...
42
43
44
45
46
...
»

Содержание 2009 HUV 4214


























































Отзывы:

Нет отзывов

Похожие инструкции для 2009 HUV 4214

Бренд: Polaris Страницы: 665

2002/24 ATV-300XS

Бренд: HER CHEE Страницы: 56

Бренд: Can-Am Страницы: 58

Raider Max 175D

Бренд: Dazon Страницы: 43

Бренд: Daymak Страницы: 33

Бренд: Dinli Страницы: 122

Бренд: Can-Am Страницы: 152

2008 DS 450 EFI X

Бренд: Can-Am Страницы: 384

2011 commander 1000

Бренд: Can-Am Страницы: 423

Sportsman 90 2011

Бренд: Polaris Страницы: 12

UTV 2x4 Series 11

Бренд: Polaris Страницы: 108

Бренд: Landoll Страницы: 88

Бренд: Kayo Страницы: 4

Raider Max 175S

Бренд: Dazon Страницы: 54

AUTOMIZER HELPING-HAND

Бренд: Labrie Страницы: 118

Бренд: UTIFORM Страницы: 85

Бренд: SMC Networks Страницы: 93

M415XT MAINTAINER

Бренд: Mauldin Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды