Husqvarna 2009 HUV 4214 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 57

background image

Engine Oil

26

Figure 18

Remove Engine Oil Filter

27

Figure 19

Coat Rubber Seal

4.

Use a clean, lint-free rag to wipe the oil filter port flange surface clean where the oil filter gasket seats.

5.

To help seal the new oil filter to the oil port flange, apply a light coat of white lithium NLGI Number 2 grease
(Dow Corning

®

BR2-Plus or equivalent) or new engine oil to the rubber seal around the outside surface of the

filter before attaching it to the oil filter port

(Figure 19)

. Install the new oil filter onto the engine oil filter port.

See following NOTE.

NOTE:

Use only engine-compatible oil filters designed for your engine.

6.

Tighten the oil filter by hand 2/3 turn after gasket contact. Do not use a band wrench or channel lock pliers.

806

Figure 20

Add Engine Oil

Page 38

2009 HUV 4214, HUV 4414, andHUV 4414-XP Owner’s Manual

«
...
38
39
40
41
42
...
»

Содержание 2009 HUV 4214


























































Отзывы:

Нет отзывов

Похожие инструкции для 2009 HUV 4214

2002/24 ATV-300XS

Бренд: HER CHEE Страницы: 56

Бренд: Moni Страницы: 27

Бренд: Tao Motor Страницы: 80

GOOSENECK LIVESTOCK

Бренд: Wilson Trailer Страницы: 80

Бренд: AC Air Technology Страницы: 46

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 92

WARRIOR YFM350XN

Бренд: Yamaha Страницы: 167

Бренд: Yamaha Страницы: 227

Бренд: Yamaha Страницы: 288

Бренд: Yamaha Страницы: 360

Бренд: Yamaha Страницы: 439

Бренд: HYOSUNG Страницы: 133

Бренд: Humbaur Страницы: 56

Бренд: Hammerhead Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды