Husqvarna 2009 HUV 4214 Скачать руководство пользователя страница 23

Страница: 23 / 57

Driving Instructions

•

Park brake:

When latched, the park brake should lock the wheels and hold the vehicle stationary on an incline

of 20% or less. To adjust park brake, remove rubber handle cover

(Figure 6)

and turn slotted adjustment screw

one revolution at a time, checking each time until park brake locks wheels and holds the vehicle stationary on
an incline of 20% or less.

•

Reverse buzzer:

If equipped with a reverse buzzer, the reverse buzzer should sound as a warning when the

Forward/Reverse handle is in the REVERSE position.

•

Steering:

The vehicle should be easy to steer and should not have any play in the steering wheel.

•

Accelerator:

After starting the engine with the key switch and placing the Forward/Reverse handle in the

FORWARD position, the vehicle should accelerate smoothly to full speed as the accelerator pedal is pressed.
When the pedal is released it should return to the original position, and the engine should idle. This vehicle
operates at a reduced speed in reverse.

•

Governor:

Check maximum vehicle speed. The vehicle should operate in forward at a maximum speed of 25

mph (40 km/h) on a level surface.

•

Differential Lock Control:

Check for proper operation.

See Controls and Indicators on page 13.

•

Front Axle Disconnect Control:

Check for proper operation.

See Controls and Indicators on page 13.

•

General:

Listen for any unusual noises such as squeaks or rattles. Check the vehicle’s ride and performance.

Have a dealer or a trained technician investigate anything unusual.

DRIVING INSTRUCTIONS

WARNING

• Only licensed drivers should be allowed to drive the vehicle.

• Before allowing anyone to drive the vehicle, make sure the driver is familiar with all controls and

operating procedures.

• No one under the age of 16 years should be allowed to drive the vehicle.

• No more than two persons per bench seat at one time. Do not allow people to ride in any part of the

vehicle that is not equipped with a seat and a safety belt. Do not allow a passenger to hold a child in
his or her lap while the vehicle is moving.

• Do not allow riders in the cargo bed.

• For night use, the vehicle must be equipped with headlights, taillights, and reflectors.

• The vehicle is not specially equipped for handicapped persons:

– Be sure all passengers are capable of securing themselves in a moving vehicle before allowing

them to ride in one.

– Be sure all persons can properly operate the vehicle prior to allowing them to drive the vehicle.

• Stop the vehicle before shifting the Forward/Reverse handle. Engine must be at idle before shifting

the Forward/Reverse handle. Failure to do so may result in injury to inattentive passengers and
(or) damage to the vehicle.

• To help avoid being struck, do not stand in front of or behind the vehicle.

• Do not leave children unattended on vehicle.

• Children requiring a child safety seat must not ride on the vehicle. Comply with state and local laws

pertaining to child safety.

• Operate the vehicle from the driver seat only.

WARNING CONTINUED ON NEXT PAGE

2009 HUV 4214, HUV 4414, andHUV 4414-XP Owner’s Manual

Page 21

Содержание 2009 HUV 4214


























































Результаты поиска

Содержание 2009 HUV 4214

Отзывы:

Похожие инструкции для 2009 HUV 4214

Бренды по названию

Популярные бренды

Husqvarna 2009 HUV 4214, Руководство пользователя

Результаты поиска

Содержание 2009 HUV 4214

Отзывы:

Похожие инструкции для 2009 HUV 4214

Бренды по названию

Популярные бренды