HURST P 630 SG Скачать руководство пользователя страница 37

Страница: 37 / 44

Fault

Check

Cause

Solution

It is frequently not

possible to couple

hose assemblies

Hydraulic fluid not

adapted to the

application situation

Hydraulic fluid must be

replaced (see chapter

"Recommended

hydraulic fluids")

Coupling defective

Coupling must be

replaced immediately

Leak in the couplings

Coupling defective

Coupling must be

replaced immediately

Leakage at the drive

shaft of the hydraulic

pump

Shaft seal defective.

Repair by an

authorised dealer, by

personnel specially

trained by HURST, or

by HURST itself

Contact an authorised HURST dealer or the HURST Customer Service Department directly

if the malfunctions cannot be rectified.

The address for the HURST Customer Service department is:

HURST

JAWS OF LIFE, INC

A Unit of IDEX Corporation

711 N. Post Road

Shelby, NC 28150 USA

Phone: (704) 487-6961

Fax:

(704) 487-7271

e-mail: [email protected]

NOTE:

In case of faults which affect the combustion engine, please also observe the instructions

in the separate operating instructions of the engine manufacturer.

Содержание P 630 SG













































Результаты поиска

Содержание P 630 SG

Отзывы:

Похожие инструкции для P 630 SG

Бренды по названию

Популярные бренды

HURST P 630 SG, Инструкция по эксплуатации

Результаты поиска

Содержание P 630 SG

Отзывы:

Похожие инструкции для P 630 SG

Бренды по названию

Популярные бренды