Humboldt HM-5940 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 38

background image

34

Initial Set up— Contact

1. Clicking on this panel provides contact information for Humboldt

Support and Service.

Contact Information

Below is a view of the Contact Information screen showing contact

information for Humboldt Support and Service.

For quickest response go to this link on our website: https://www.

humboldtmfg.com/support and fi ll in the support form.

This will

provide us with the necessary information to assist you and you will be

added to the next position in the support queue.

You can also email Humboldt Support at [email protected]

or Humboldt Service at [email protected]. Please
include contact information and a detailed description of your
reason for contact.

«
...
32
33
34
35
36
...
»

Содержание HM-5940







































Отзывы:

Нет отзывов

Похожие инструкции для HM-5940

Бренд: NARGESA Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Litmann Quality 3100

Бренд: 3M Страницы: 2

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Palmer Страницы: 2

Бренд: Fast Страницы: 60

Бренд: Vaillant Страницы: 76

Бренд: H2flow Страницы: 2

Бренд: V-TAC Страницы: 27

Бренд: Yacht Sentinel Страницы: 32

Бренд: X-FLOC Страницы: 35

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

TOTAL KNEE 1900

Бренд: Össur Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды