Huawei TaiShan 200 Series Скачать руководство пользователя страница 30

Страница: 30 / 132

Table 2-10 Description of SAS/SATA drive indicators

Drive Activity

Indicator (Green

Indicator)

Drive Fault

Indicator (Yellow

Indicator)

Description

Steady on

Off

The drive is in position.

Blinking at 4 Hz

Off

Data is being read or written normally,

or data on the primary drive is being

rebuilt.

Steady on

Blinking at 1 Hz

The drive is being located by the RAID

controller card.

Blinking at 1 Hz

The data on the secondary drive is

being rebuilt.

Off

Steady on

A member drive in the RAID array is

removed.

Steady on

A member drive in the RAID array is

faulty.

2.6.3 NVMe SSD Indicators

Figure 2-20

shows the NVMe SSD indicators.

Figure 2-20 NVMe SSD indicators

Table 2-11 NVMe SSD indicators

Drive Activity

Indicator

(Green

Indicator)

Drive Fault

Indicator

(Yellow

Indicator)

State Description

Off

The NVMe SSD cannot be detected.

Steady green

Off

The NVMe SSD is detected and working

properly.

Blinking green

(2 Hz)

Off

Data is being read from or written to the

NVMe SSD.

Off

Blinking yellow

(2 Hz)

The NVMe SSD is being located or hot-

swapped.

Off

Blinking yellow

at 0.5 Hz

The NVMe SSD completes the hot removal

process and is removable.

TaiShan 200 Server

User Guide (Model 2280)

2 Components

Issue 04 (2020-01-16)

Содержание TaiShan 200 Series





































































































































Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды

Huawei TaiShan 200 Series, Руководство пользователя

Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды