Huawei TaiShan 200 Series Скачать руководство пользователя страница 22

Страница: 22 / 132

Table 2-4 Ports on the rear panel

Port

Type

Quanti

Description

VGA port

DB15

The VGA port is connected to a

terminal, such as a monitor or

physical KVM.

USB port

USB 3.0

The USB ports allow USB devices to

be connected to the server.

NOTE

Before connecting an external USB device,

check that the USB device functions

properly. A server may operate abnormally

if an abnormal USB device is connected.

Management

network port

RJ45

This 1000 Mbps Ethernet port is used

for server management, and supports

10/100/1000 Mbps auto-negotiation.

Serial port

RJ45

The serial port is used as the system

serial port by default. You can set it as

the iBMC serial port by using the

iBMC command. This port is used for

debugging.

NOTE

For details about how to set the system

serial port as the iBMC serial, see Logging

In over the Serial Port in

8.2 Logging In

to the iBMC CLI

GE electrical

port

RJ45

4/8

● Each FlexIO card provides four GE

electrical ports. A maximum of

eight GE electrical ports can be

provided through the two FlexIO

cards.

● This 1000 Mbps Ethernet port is

used for FlexIO card, and supports

10/100/1000 Mbps auto-

negotiation.

25GE optical

port

SFP28

A FlexIO card can provide a maximum

of four 25GE optical ports.

NOTE

The 25GE optical ports support rate

adaptation to 10GE, and optical modules

of different rates are required.

TaiShan 200 Server

User Guide (Model 2280)

2 Components

Issue 04 (2020-01-16)

Содержание TaiShan 200 Series





































































































































Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды

Huawei TaiShan 200 Series, Руководство пользователя

Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды