Huawei TaiShan 200 Series Скачать руководство пользователя страница 24

Страница: 24 / 132

Indicator

State Description

UID indicator

The UID indicator helps identify and locate

a device.
● Off: The device is not being located.
● Blinking blue (blinking 255 seconds):

The device has been located and is

differentiated from other devices that

have also been located.

● Steady blue: The device is being

located.

NOTE

You can turn on, turn off, or blink the UID

indicator by pressing the UID button or

remotely running a command on the iBMC CLI.

25 GE

optical

port

Transmission rate

indicator

● Steady green: The data transmission

rate is 25 Gbit/s.

● Steady yellow: The data transmission

rate is 10 Gbit/s.

● Off: The network port is not connected.

Connection status

indicator/Data

transmission status

indicator

● Steady green: The network port is

properly connected.

● Blinking green: Data is being

transmitted.

● Off: The network port is not connected.

PSU indicator

● Steady green: The power input and

output are normal.

● Steady orange: The input is normal, but

no power output is supplied due to

overheat protection, overcurrent

protection, short circuit protection,

output overvoltage protection, or some

component failures.

● Blinking green at 1 Hz:

– The input is normal, the server is

standby.

– The input is overvoltage or

undervoltage. For details, see

TaiShan Rack Server iBMC Alarm

Handling

● Blinking green at 4 Hz: under online

PSU firmware upgrade.

● Off: No power is supplied.

TaiShan 200 Server

User Guide (Model 2280)

2 Components

Issue 04 (2020-01-16)

Содержание TaiShan 200 Series





































































































































Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды

Huawei TaiShan 200 Series, Руководство пользователя

Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды