Huawei TaiShan 200 Series Скачать руководство пользователя

Страница: 12 / 132

Figure 1-4 Logical structure of the 2280 server (Kunpeng 920 7260, 5250, or 5230

processor)

●

The server supports two Huawei-developed Kunpeng 920 7260, 5250, or 5230

processors, each of which supports 16 DDR4 DIMMs.

●

CPU1 and CPU2 are interconnected through two Hydra buses. The maximum

transmission rate of a single bus is 30 Gbit/s.

●

The server can come with an Ethernet FlexIO card with four GE or 25GE ports,

which are connected to the CPUs through the high-speed SerDes interface.

●

The Ethernet FlexIO card provides four GE ports, which are connected to the

CPUs through the high-speed SerDes interface.

TaiShan 200 Server

User Guide (Model 2280)

1 Overview

Issue 04 (2020-01-16)

Содержание TaiShan 200 Series





































































































































Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды

Huawei TaiShan 200 Series, Руководство пользователя

Результаты поиска

Содержание TaiShan 200 Series

Отзывы:

Похожие инструкции для TaiShan 200 Series

Бренды по названию

Популярные бренды