Huawei TaiShan 200 23280 Скачать руководство пользователя страница 53

Страница: 53 / 191

●

Both ends of an ESD wrist strap must be in good contact. One end contacts

your bare skin, and the other is securely inserted into the ESD jack in the

chassis. For details, see

5.3.2 ESD Wrist Strap

●

During parts replacement, keep new server components in ESD bags before

installation, and place removed server components on conductive mats for

temporary storage.

●

Do not touch welding points, pins, or exposed circuits.

5.3.2 ESD Wrist Strap

A cabinet or chassis is properly grounded.

Step 1 Put on the ESD wrist strap. See

Figure 5-2

Figure 5-2 Wearing an ESD wrist strap

Step 2 Tighten the ESD wrist strap to ensure that it is in good contact with your bare

skin.

Step 3 Insert the ground terminal of the ESD wrist strap into the ESD jack in a cabinet or

chassis.

----End

5.4 Environmental Requirements

NO TE

● For details about the safety precautions to be observed when you install or replace

servers and their parts, see the

Huawei Server Safety Information

● Suitable for mounting on concrete or other non-combustible surface only.

5.4.1 Space and Airflow Requirements

To allow for servicing and adequate airflow, observe the following space and

airflow requirements:
●

Install the server in an access-restricted area.

●

Keep the area in which the server is located clean and tidy.

●

To facilitate heat dissipation and maintenance, keep a clearance of 800 mm

(31.50 in.) between walls and the front and rear doors of the cabinet.

●

Do not block the air intake vents. Otherwise, air intaking and heat dissipation

will be affected.

TaiShan 200 Server (Model 2280)

User Guide

5 Installation and Configuration

Issue 09 (2021-01-12)

Содержание TaiShan 200 23280
































































































































































































Результаты поиска

Содержание TaiShan 200 23280

Отзывы:

Похожие инструкции для TaiShan 200 23280

Бренды по названию

Популярные бренды

Huawei TaiShan 200 23280, Руководство пользователя

Результаты поиска

Содержание TaiShan 200 23280

Отзывы:

Похожие инструкции для TaiShan 200 23280

Бренды по названию

Популярные бренды