Huawei SUN2000-196KTL-H0 Скачать руководство пользователя страница 68

Страница: 68 / 109

Figure 7-10 Power grid parameters (special user)

----End

Parameters

No.

Parameter

Description

Grid Code

Set this parameter based on the grid code of the country

or region where the inverter is used and the inverter

application scenario.

Isolation settings

Set the working mode of the inverter based on the

grounding status at DC side and the connection to the

power grid.

Output mode

Specifies whether the inverter output has a neutral wire

based on the application scenario.

Automatically start upon

grid recovery

Specifies whether to allow the inverter to automatically

start after the power grid recovers.

Grid connected recovery

time from grid faults (s)

Specifies the time after which the inverter begins

restarting after the power grid recovers.

Grid reconnection voltage

upper limit (V)

The standards of certain countries and regions require

that after the inverter shuts down for protection due to a

fault, if the power grid voltage is higher than Grid

reconnection voltage upper limit, the inverter is not

allowed to reconnect to the grid.

Grid reconnection voltage

lower limit (V)

The standards of certain countries and regions require

that after the inverter shuts down for protection due to a

fault, if the power grid voltage is lower than Grid

reconnection voltage lower limit, the inverter is not

allowed to reconnect to the grid.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

User Manual

7 Man-Machine Interactions

Issue 02 (2020-10-30)

Содержание SUN2000-196KTL-H0














































































































Результаты поиска

Содержание SUN2000-196KTL-H0

Отзывы:

Бренды по названию

Популярные бренды

Huawei SUN2000-196KTL-H0, Руководство пользователя

Результаты поиска

Содержание SUN2000-196KTL-H0

Отзывы:

Бренды по названию

Популярные бренды