Huawei SUN2000-196KTL-H0 Скачать руководство пользователя страница 40

Страница: 40 / 109

5.6 Connecting the AC Output Power Cable

Precautions

A three-phase AC switch should be installed on the AC side of the inverter. To

ensure that the inverter can safely disconnect itself from the power grid when an

exception occurs, select a proper overcurrent protection device in compliance with

local power distribution regulations.

WARNING

Do not connect loads between the inverter and the AC switch.

The inverter is integrated with a comprehensive residual current detection unit to

distinguish fault current from residual current. Upon detecting that the residual

current exceeds the threshold, the inverter immediately disconnects from the

power grid.

Cable Connection Precautions

NO TICE

● The cable outer diameter can be measured using the ruler sticker in the

maintenance compartment.

● Ensure that the cable jacket is in the maintenance compartment.
● Ensure that the AC output power cable is secured. Failing to do so may cause

the solar inverter to malfunction or damage to its terminal block by issues such

as overheating.

●

The ground point on the enclosure is preferred to connect to the PE cable for

the inverter.

●

The PE point in the maintenance compartment is used for connecting to the

PE cable included in the multi-core AC power cable.

●

There are two ground points on the chassis shell and you only need either of

them.

●

It is recommended that the PE cable of the inverter be connected to a nearby

ground point. For a system with multiple inverters connected in parallel,

connect the ground points of all inverters to ensure equipotential connections

to ground cables.

Cable Specifications

●

If you connect a ground cable to the ground point on the chassis shell, you

are advised to use a three-core (L1, L2, and L3) outdoor cable or three single-

core outdoor cables.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

User Manual

5 Electrical Connections

Issue 02 (2020-10-30)

Содержание SUN2000-196KTL-H0














































































































Результаты поиска

Содержание SUN2000-196KTL-H0

Отзывы:

Бренды по названию

Популярные бренды

Huawei SUN2000-196KTL-H0, Руководство пользователя

Результаты поиска

Содержание SUN2000-196KTL-H0

Отзывы:

Бренды по названию

Популярные бренды