Huawei RTN 380H Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 29

background image

Installation Reference

48/49 >>

Installing the Outdoor Optical Splitter

Optional: pole-mounting

Install the pole assembly on the pole.

Assembly

Hold hoop

Loosen the screw on the hold hoop.

Install the pole assembly on the pole.

Tighten the
screw on the
hold hoop.

Tighten the
hold hoop.

Partially
tighten the
hold hoop.

Complete installation of the pole
assembly.

Fix the case on the pole assembly and tighten the lower hold hoop.

Fix the upper end of the case and then the lower end.

Route in and fix cables.

5

Determine the holes through which fibers are routed in and remove the hole
blocks.

Connected to the fiber outlet
on the main RTN 380H.

Connected to the fiber
outlet on the standby
RTN 380H.

Connected to the fiber outlet
on the customer equipment.

Hole blocks

Outdoor fiber trough

Fix hose clamps on outdoor fibers.

Hose clamp

Hooks to fix
hose clamps

4

Tighten the
hold hoop.

1

2

«
...
23
24
25
26
27
...
»

Содержание RTN 380H






























Отзывы:

Нет отзывов

Похожие инструкции для RTN 380H

Бренд: Radio Shack Страницы: 52

Бренд: Eaton Страницы: 16

Бренд: Datalogic Страницы: 15

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Yoshitake Страницы: 4

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

Бренд: Rabbit Страницы: 12

Бренд: DSC Страницы: 16

Бренд: jbc Страницы: 16

Бренд: Weidmüller Страницы: 18

Бренд: Vaniman Страницы: 2

Бренд: Samson Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды