Huawei pRRU3901 Скачать руководство пользователя страница 46

Страница: 46 / 52

Figure 10-5

Removing the pRRU housing

NOTE

The pRRU housing and the RF daughter board can be secured using either Phillips screws or protection
screws, requiring the same installation operations. This section uses Phillips screws as an example to
describe the installation operations.

Keep the Phillips screw secure for future use.

Step 10

Record positions of the RF daughter boards on the pRRU mother board, as shown in

Figure

10-6

. The following section assumes that the pRRU has two RF daughter boards.

Figure 10-6

Recording the installation positions of RF daughter boards

Step 11

Remove the RF daughter board in slot S1 and that in slot S2 in the same way.

NOTICE

Hold the RF daughter board tightly when pulling the handle to prevent the RF daughter board
from falling.

LampSite
Site Maintenance Guide

10 Replacing the pDock Mother Board

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Содержание pRRU3901





















































Результаты поиска

Содержание pRRU3901

Отзывы:

Похожие инструкции для pRRU3901

Бренды по названию

Популярные бренды

Huawei pRRU3901, Руководство по обслуживанию

Результаты поиска

Содержание pRRU3901

Отзывы:

Похожие инструкции для pRRU3901

Бренды по названию

Популярные бренды